The cirros image was rebuilt against the 3.13.0-83 kernel, drivers e1000e, igbvf...

[packages/trusty/cirros-testvm.git] / cirros-testvm / src-cirros / buildroot-2015.05 / board / avnet / zedboard / readme.txt

diff --git a/cirros-testvm/src-cirros/buildroot-2015.05/board/avnet/zedboard/readme.txt b/cirros-testvm/src-cirros/buildroot-2015.05/board/avnet/zedboard/readme.txt
new file mode 100644 (file)
index 0000000..a3f1f3e
--- /dev/null
+++ b/cirros-testvm/src-cirros/buildroot-2015.05/board/avnet/zedboard/readme.txt
@@ -0,0 +1,72 @@
+This is the buildroot board support for the Avnet Zedboard. The Zedboard is
+a development board based on the Xilinx Zynq-7000 based All-Programmable
+System-On-Chip.
+
+Zedboard information including schematics, reference designs, and manuals are
+available from http://www.zedboard.org .
+
+The U-Boot firmware for the Xilinx Zynq All Programmable SoC depends
+on some proprietary code. This dependency consists of a pair of
+files are available from the Xilinx SDK installation.
+
+You will need these files from Xilinx SDK installation to generate
+the U-Boot firmware:
+       ps7_init.c
+       ps7_init.h
+
+Buildroot will create the following files and place them in the
+<output>/images directory.
+       zynq-zed.dtb
+       rootfs.cpio.uboot
+       uImage
+       u-boot.img
+       boot.bin
+
+
+uboot.bin  -- U-Boot SPL w/ Xilinx boot.bin wrapper
+---------------------------------------------------
+
+Due to licensing issues, the files ps7_init.c/h are not able to be
+distributed with the U-Boot source code.  These files are required to make a
+boot.bin file.
+
+If you already have the Xilinx tools installed, the following sequence will
+unpack, patch and build the rfs, kernel, uboot, and uboot-spl.
+
+make zedboard_defconfig
+make uboot-patch
+cp ${XILINX}/ISE_DS/EDK/sw/lib/hwplatform_templates/zed_hw_platform/ps7_init.{c,h} \
+output/build/uboot-xilinx-v2014.1/board/xilinx/zynq/
+
+After copying these files into the U-Boot source tree, you can
+continue the build with:
+
+make
+
+*Notice*
+While the build will successfully complete without the ps7_init.*
+files,  the uboot.bin file generated by this configuration will not
+function properly on the Zedboard.  Therefore, it is imperative that
+the ps7_init.* files be copied into the U-Boot source tree any time
+the clean, or uboot-dirclean targets are made.
+
+
+Resulting system
+----------------
+A FAT32 partition should be created at the beginning of the SD Card
+and the following files should be installed:
+       /boot.bin
+       /devicetree.dtb
+       /uImage
+       /uramdisk.image.gz
+       /u-boot.img
+
+
+All needed files can be taken from output/images/
+
+boot.bin, uImage and u-boot.img are direct copies of the same files
+available on output/images/
+
+devicetree.dtb is just zynq-zed.dtb renamed.
+
+uramdisk.image.gz is rootfs.cpio.uboot renamed