README updates

Feature lists for `firewall` providers were out of date, and
`physdev_in` and `physdev_out` were listed as features instead of
parameters.

diff --git a/README.markdown b/README.markdown
index e21937c6569c2773e415707c9bfe6548513fa4fb..d14143ed7390f0e82604b473aa6eccc10851c10c 100644 (file)
--- a/README.markdown
+++ b/README.markdown
@@ -339,12 +339,12 @@ This type enables you to manage firewall rules within Puppet.
 
  * `ip6tables`: Ip6tables type provider
     * Required binaries: `ip6tables-save`, `ip6tables`.
-    * Supported features: `connection_limiting`, `dnat`, `hop_limiting`, `icmp_match`, `interface_match`, `ipsec_dir`, `ipsec_policy`, `ipset`, `iptables`, `isfirstfrag`, `ishasmorefrags`, `islastfrag`, `log_level`, `log_prefix`, `mark`, `mask`, `owner`, `physdev_in`, `physdev_out`, `pkttype`, `rate_limiting`, `recent_limiting`, `reject_type`, `snat`, `socket`, `state_match`, `tcp_flags`.
+    * Supported features: `address_type`, `connection_limiting`, `dnat`, `hop_limiting`, `icmp_match`, `interface_match`, `iprange`, `ipsec_dir`, `ipsec_policy`, `ipset`, `iptables`, `isfirstfrag`, `ishasmorefrags`, `islastfrag`, `log_level`, `log_prefix`, `mark`, `mask`, `owner`, `pkttype`, `rate_limiting`, `recent_limiting`, `reject_type`, `snat`, `socket`, `state_match`, `tcp_flags`.
 
 * `iptables`: Iptables type provider
     * Required binaries: `iptables-save`, `iptables`.
     * Default for `kernel` == `linux`.
-    * Supported features: `address_type`, `connection_limiting`, `dnat`, `icmp_match`, `interface_match`, `iprange`, `ipsec_dir`, `ipsec_policy`, `ipset`, `iptables`, `isfragment`, `log_level`, `log_prefix`, `mark`, `mask`, `owner`, `physdev_in`, `physdev_out`, `pkttype`, `rate_limiting`, `recent_limiting`, `reject_type`, `snat`, `socket`, `state_match`, `tcp_flags`, `netmap`.
+    * Supported features: `address_type`, `connection_limiting`, `dnat`, `icmp_match`, `interface_match`, `iprange`, `ipsec_dir`, `ipsec_policy`, `ipset`, `iptables`, `isfragment`, `log_level`, `log_prefix`, `mark`, `mask`, `netmap`, `owner`, `pkttype`, `rate_limiting`, `recent_limiting`, `reject_type`, `snat`, `socket`, `state_match`, `tcp_flags`.
 
 **Autorequires:**
 
@@ -514,6 +514,10 @@ firewall { '999 this runs last':
 
 * `outiface`: Output interface to filter on. Values must match '/^!?\s?[a-zA-Z0-9\-\._\+\:]+$/'.  Requires the `interface_match` feature.  Supports interface alias (eth0:0) and negation.
 
+* `physdev_in`: Match if the packet is entering a bridge from the given interface. Values must match '/^[a-zA-Z0-9\-\._\+]+$/'.
+
+* `physdev_out`: Match if the packet is leaving a bridge via the given interface. Values must match '/^[a-zA-Z0-9\-\._\+]+$/'.
+
 * `pkttype`: Sets the packet type to match. Valid values are: 'unicast', 'broadcast', and'multicast'. Requires the `pkttype` feature.
 
 * `port`: The destination or source port to match for this filter (if the protocol supports ports). Will accept a single element or an array. For some firewall providers you can pass a range of ports in the format: 'start number-end number'. For example, '1-1024' would cover ports 1 to 1024.